Figures
Abstract
In the last twenty years new antibacterial agents approved by the U.S. FDA decreased whereas in parallel the resistance situation of multi-resistant bacteria increased. Thus, community and nosocomial acquired infections of resistant bacteria led to a decrease in the efficacy of standard therapy, prolonging treatment time and increasing healthcare costs. Therefore, the aim of this work was to demonstrate the applicability of cold atmospheric plasma for decolonisation of Gram-positive (Methicillin-resistant Staphylococcus aureus (MRSA), Methicillin-sensitive Staphylococcus aureus) and Gram-negative bacteria (E. coli) using an ex vivo pig skin model. Freshly excised skin samples were taken from six month old female pigs (breed: Pietrain). After application of pure bacteria on the surface of the explants these were treated with cold atmospheric plasma for up to 15 min. Two different plasma devices were evaluated. A decolonisation efficacy of 3 log10 steps was achieved already after 6 min of plasma treatment. Longer plasma treatment times achieved a killing rate of 5 log10 steps independently from the applied bacteria strains. Histological evaluations of untreated and treated skin areas upon cold atmospheric plasma treatment within 24 h showed no morphological changes as well as no significant degree of necrosis or apoptosis determined by the TUNEL-assay indicating that the porcine skin is still vital. This study demonstrates for the first time that cold atmospheric plasma is able to very efficiently kill bacteria applied to an intact skin surface using an ex vivo porcine skin model. The results emphasize the potential of cold atmospheric plasma as a new possible treatment option for decolonisation of human skin from bacteria in patients in the future without harming the surrounding tissue.
Citation: Maisch T, Shimizu T, Li Y-F, Heinlin J, Karrer S, Morfill G, et al. (2012) Decolonisation of MRSA, S. aureus and E. coli by Cold-Atmospheric Plasma Using a Porcine Skin Model In Vitro. PLoS ONE 7(4): e34610. https://doi.org/10.1371/journal.pone.0034610
Editor: Michael Otto, National Institutes of Health, United States of America
Received: October 19, 2011; Accepted: March 5, 2012; Published: April 27, 2012
Copyright: © 2012 Maisch et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.
Funding: Dr. Tim Maisch was supported by a grant (M.TT.A.EXT00002) of the Max Planck Institute for Extraterrestrial Physics, Garching, Germany. The funders had no role in study design, data collection and analysis, decision to publish, or preparation of the manuscript.
Competing interests: The authors have declared that no competing interests exist.
Introduction
Eradication of multiresistant superbugs is one of the clinical challenges of the 21st century [1]. In addition the situation will further exacerbate, because the pipeline of new antibiotics is not fully straight. The Infectious Diseases Society of America (IDSA) highlights that, over the past several years, the number of new antibacterial drugs approved continues to decrease [2], [3]. Only three of the eight antibiotics approved within the last decade act towards a new mechanism of action, whereas all the others are only modifications of already known antibiotics. In parallel, the resistance of S. aureus increased substantially: Nowadays a total of ∼21% of Staphylococcus aureus in Germany are resistant to methicillin/oxacillin [4]. Klevens reported that the overall increase of methicillin-resistant S. aureus (MRSA) resistance was 3.1% per year in USA, based on a linear model from 1992–2003 [5]. Thus, there is great interest in new antimicrobial strategies to overcome the lack of new anti-invectives. Recently cold atmospheric plasma has demonstrated both bactericidal, virucidal and fungicidal properties due to the generation of reactive species and charged particles [6], [7], [8]. Numerous studies demonstrated the effectiveness of gas-discharge or cold atmospheric plasmas for killing especially planktonic microorganisms [7], [9], [10], [11]. Furthermore a successful disinfection of methicillin-resistant Staphylococcus aureus and Staphylococcus epidermidis biofilms was demonstrated using a remote non-thermal gas plasma [12].
In the context of decreasing numbers of new antibacterial drugs and increasing resistance of bacteria the effective disinfection of hospital surfaces is of major interest as an important factor in preventing hospital-acquired infections. First attempts were shown by Burts et al. who was able to demonstrate that disinfection of hospital pagers experimentally coated with MRSA could be achieved within 30 seconds of plasma treatment [13]. In general cold atmospheric plasma, which means less than 40°C at the point of application, can be produced in air in order to produce reactive molecules like atoms, ions and radicals. This chemical “cocktail” of reactive species can be used for different biomedical applications. The killing efficacies of plasma were in the same range as standard antimicrobial agents, up to 3–5 log10 steps [13]. However, to our knowledge, there are only few reports about the use of cold atmospheric plasma for decolonization of bacteria applied to vital skin surfaces [14], [15]. Lademann et al. for example used a plasma tissue tolerable plasma jet and achieved a reduction of the bacteria load of 94% using an ex vivo ear pig skin model [15]. However this plasma jet is able to disinfect only small skin areas (inhibition zone 2 mm) and was moved with an average velocity of 10 mm/sec on the skin surface.
For demonstrating the killing efficacies of new disinfecting agents an ex vivo porcine skin model was developed in our lab [16]. This model was used, as it serves as an alternative skin model for human skin based on many similarities regarding behaviour, composition, histological, physiological and permeability properties [17], [18]. The challenge of the antimicrobial plasma treatment is to find appropriate parameters which inactivate bacteria without harming the surrounding tissue. Therefore the present study was performed to evaluate the efficacy of two different cold-atmospheric plasma devices for decolonisation of ≥3 log10 steps (≥99.9%) of S. aureus, MRSA and E. coli on large skin areas when these bacteria were applied to an ex vivo porcine skin model.
Materials and Methods
Bacterial strains
The bacterial strains Escherichia coli (atcc 25922), methicillin-sensitive Staphylococcus aureus (atcc 25923) and two methicillin-resistant Staphylococcus aureus (MRSA: atcc BAA-44; attcc 43300) were grown aerobically at 37°C in Mueller-Hinton broth (Carl Roth GmbH+Co. KG, Karlsruhe, Germany). A 500 µl portion of an overnight bacteria culture (3 ml) was transferred to 50 ml of fresh BHI media and grown at 37°C on an orbital shaker. When the cultures reached the stationary phase of growth, the bacteria were harvested by centrifugation (200 g, 15 min), washed with 10 mM phosphate-buffered saline (PBS; Biochrom, Berlin, Germany) at pH 7.4 containing 2.7 mM KCl and 0.14 M NaCl and suspended in PBS at an optical density of 0.6 at 600 nm corresponding to 106–7 bacteria ml−1.
Preparation of pig skin
Fresh skin from six month old female pigs (breed: Pietrain) was obtained from a local slaughterhouse (Metzgerei Stierstorfer, Wenzenbach, Germany). The preparation was done as already published [16]. Briefly, the excised skin was washed with water, epilated with a dry razor and the adipose tissue beneath the dermis was removed with a scalpel. Then the skin was cut under sterile conditions into 2×2 cm2 pieces, placed in a Petri dish and embedded with Hepes Agar. The surface of the embedded skin was then incubated with 70% ethanol for 5 min to reduce the number of resident bacteria. After three washing steps with sterile PBS, a known number of bacteria (106–7 ml−1 CFU) were applied to the skin and the treatment with cold atmospheric plasma was performed.
Plasma devices
Two different cold atmospheric plasma devices were evaluated.
FlatPlaSter.
The FlatPlaSter plasma device is a box made out of plastic (Teflon and polyoxymethylene) incorporating an electrode for the plasma production inside as shown in figure 1A. On one side of the box, a door is installed. By closing the door the produced plasma gas cannot escape and therefore is confined inside. This plasma device is designed for the treatment of a 96-well plate (sample), so that the maximum treated area equals 9×13 cm2. The plasma electrode is placed above the sample and the distance between the electrode and the sample is adjustable. In our experiments, the distance to the pig skin surfaces was set to 6 mm. By using the ambient air a plasma discharge is ignited with the SMD (Surface Micro-Discharge) plasma technique [19]. The plasma electrode consists of a 0.5 mm thick Teflon plate sandwiched by a brass planar plate and a stainless steel mesh grid (line width 2 mm, opening 10 mm, height 1.5 mm). High sinusoidal voltage of 9 kVpp with 1 kHz in frequency was applied between the brass electrode and the mesh electrode thereby producing the plasma discharges on the mesh side of the SMD electrode as shown in figure 1B. The power consumption for the plasma discharge was approximately 0.02 W/cm2 measured with the Lissajous method using a 0.1 µF capacitance.
a) The FlatPlaSter contains one SMD electrode and the samples (to treat) are placed inside the device below the electrode. In this study the distance between the electrode and the sample surface was fixed at 6 mm. b) left: The plasma discharge is shown. On the mesh-side of the electrode, the SMD plasma was produced. c) right: The spectrum of the SMD plasma observed in front of the electrode with a distance of 6 mm is shown. The UV components in the range between 280–400 nm are mainly produced from nitrogen molecules excited by electrons.
miniFlatPlaSter.
The plasma device (miniFlatPlaSter), the sketch is shown in Fig. 2, is equipped with a surface micro-discharge (SMD) electrode. This device was designed for portable usage and the high voltage power supply and the accumulators are incorporated. The SMD electrode consists of a copper foil layer (around 0.2 mm thick), a glass Epoxy board (1 mm thick), and a stainless steel mesh. The plasma is ignited on the mesh side of the electrode by applying a high voltage signal between the copper foil and the mesh. The voltage signal is pulse-like with a peak-to-peak voltage of approximately 7 kV and a repetition frequency of approximately 6.75 kHz. The size of the electrode is 28 mm in diameter and the power consumption is approximately 0.5 W/cm2.
The portable plasma device is equipped with a high voltage power supply, accumulators, and a surface micro-discharge (SMD) electrode. The SMD electrode consists of a copper foil layer (around 0.2 mm thick), an Epoxy board (1 mm thick), and a stainless steel mesh of 28 mm in diameter. The plasma device was fixed above the ex vivo skin embedded in Hepes-Agar.
Plasma treatment
100 µl of bacteria (∼106–7/ml) was applied to the epidermis of each skin sample. Then the bacteria suspension was spread over the complete skin area of interest using a sterile inoculation loop. The samples were placed under a laminar flow cabinet for 60 min until they were visibly dry. Different plasma treatment times were investigated to determine the antimicrobial decolonization effect.
Quantification of plasma inactivation efficacy
Post plasma treatment a colony forming unit assay (CFU) was performed to determine the surviving bacteria. A sterile cotton-tipped rod was used to remove bacteria from the epidermis. For each skin sample a cotton-tipped rod was moistened in sampling buffer (0.1% Tween80, 0.0075 M phosphate puffer, pH 7.9) before swabbing the entire surface three times. First the recovery efficacy was tested to establish the range of viable numbers of CFU per ml of untreated skin samples, which was in accordance with already published data [16]. A reproducible correlation between three swabbing steps and the recovery efficiency of bacteria applied to the skin could be evaluated (data not shown). Survived bacteria were detected with the Miles and Misra technique for viable counts [20]. Serially diluted aliquots (20 µl) of treated and untreated samples were plated on Mueller-Hinton agar, and the number of CFU per millilitre was counted after 24 h of incubation at 37°C.
Histology and histochemistry
Viability of each porcine skin sample was tested by detection of dead cells using the in situ Cell Death Detection Kit according to the manufacturer's protocol (Roche, Penzberg, Germany). A detailed description of the methodology is published elsewhere [16]. Briefly, biopsies of porcine skin samples were embedded in paraffin and sections of 3 µm thickness were cut and mounted on microscope slides (SuperFrost Plus, Menzel Glasbearbeitungswerk GmbH & Co. KG, Braunschweig, Germany). Sections were permeabilised and treated with 3% of hydrogen peroxide to block endogenous peroxidase. Thereafter a TUNEL-reaction was done according to the manufacturer's protocol. Labelling of DNA strand breaks was done by addition of terminal deoxynucleotidyl transferase, which catalyzes polymerization of fluorescein-labelled nucleotides to free 3′OH DNA ends in a template-independent manner. Incorporated fluorescein was detected using a fluorescence microscope (Zeiss Axiotech, Goettingen, Germnay) with an appropriate dual-band filter set (Omega opticals, Brattleboro, VT, USA) for excitation (λex = 475±40 nm) and emission (λem = 535±35 nm). After substrate reaction, the slides were co-stained with DAPI (λex = 365±50 nm; λem = 450±58 nm) to visualize all nuclei. Fluorescence images were superimposed with an image processing program (Image-Pro Plus 5.0; Media Cybernetics, Silver Spring, MD, USA). Negative (no addition of terminal deoxynucleotidyl transferase or the labelled nucleotide mixture of the TUNEL-reaction) and positive controls (addition of DNAse I to induce DNA strand breaks) were included in each experimental set up. The presence of dead cells within the epidermis was defined as green stained nuclei with granular or sometimes fragmented cell nuclei, whereas blue stained cells are negative (DAPI). The number of stained (dead) cells per 100 cells was scored on three individual slides. The number of apoptotic cells was calculated as a percentage of the total number of counted cells as described previously by Schacht et al. [21].
Statistical methods
All results are shown as medians, including the 25% and 75% quartiles, which were calculated from the values of at least 3 independent experiments, each experiment was conducted in triplicates, with Prism 4 for Windows (GraphPad Software Inc., San Diego, CA, U.S.A). The calculation (reduction of CFU/ml) was referred to the untreated controls (non plasma treated). In Figs. 3 and 4, medians on or below the dotted horizontal line in red or green represent ≥99.9% efficacy or ≥99.999% of bacteria cell killing corresponding to at least more than three magnitudes or five magnitudes of log10 reduction compared to matching untreated controls (non plasma treated). A reduction of at least three magnitudes of log10 of viable median numbers of bacteria cells was stated as biologically relevant with regard to the guidelines of hand hygiene [22].
Cold atmospheric plasma treatment of (A) S. aureus (106–7/ml) (D-value = 3.7 min) and (B) E. coli (106–7/ml) (D-value = 3.71 min) applied to ex vivo skin using the FlatPlaSter device. Different plasma treatment times were tested [sec]. A CFU assay was performed immediately after the plasma treatment. Black dotted line: baseline of viable bacteria per ml; red dotted line: reduction of three log10 steps of viable bacteria (99.9%); green dotted line: reduction of five log10 steps of viable bacteria (99.999%). (n = 6, median ± interquartile range).
Cold atmospheric plasma treatment of MRSA (BAA-44) (106–7/ml) applied to ex vivo skin using the FlatPlaSter device. Different plasma treatment times were tested [min]. A CFU assay was performed immediately after the plasma treatment. Black dotted line: baseline of viable bacteria per ml; red dotted line: reduction of three log10 steps of viable bacteria (99.9%); green dotted line: reduction of five log10 steps of viable bacteria (99.999%). (n = 6, median ± interquartile range).
Calculation of D-value
The death-value (D-value) for each microorganism was defined as the time which is required for one log10 or 90% reduction of the initial bacteria number for the specific plasma treatment condition [23].
Results
Plasma characteristics
The cold atmospheric plasmas produced in this study deliver various agents to the samples: reactive oxygen and nitrogen species (NO, NO2, O3, OH, O*, etc.), charged particles (electrons, ions), photons (UV, visible), and heat.
In our experiments, the thermal effect can be ruled out because the increase in the gas temperature was at maximum 4 degrees for 10 minutes of plasma operation.
Due to the distance between the electrode and the sample in our experimental setup (approximately 6 mm), the impact of charged particles (low density around the samples) is very small.
The emitted UV light can be mainly observed from the N2 positive system between 280 and 420 nm in wavelength (see spectrum in fig. 1C). In addition peaks in the UVC region resulting from the NO γ system can be detected. The UV power density equals 25 nW/cm2. Furthermore it was confirmed that the UV photons (emitted by the plasma) alone did not have any bactericidal effect for a treatment time of up to 120 s. These experiments were carried out by placing a quartz glass plate between the electrode and the respective bacteria samples, so that only the UV light produced by the plasma could pass (data not shown).
Taking all this into account, the main agents which contribute to the inactivation of bacteria in this study are reactive species. As already mentioned, many reactive species are produced by the plasma and all of them can react with the samples. For example, the ozone concentration in the FlatPlaSter (see figure 1A) was at maximum 500 ppm and the concentration of NO2 was around a few ppm.
Regarding the two used plasma devices, FlatPlaSter and miniFlatPlaSter, there are no differences in property - both are based on the same SMD technology. Of course, the densities of reactive species, etc. were different because the discharge area, discharge volume, and power input were different.
Time-dependent cold-atmospheric plasma toxicity against S. aureus, MRSA and E. coli
First the antimicrobial effect of cold atmospheric plasma was tested against different antibiotic sensitive and resistant bacteria strains using the FlaPlaSter device (fig. 3 & 4). The data indicate that S. aureus, MRSA or E. coli were killed depending on the plasma treatment time. There was a considerable reduction of CFU ml−1 of 3 log10 steps for S. aureus (D-value = 3.7 min) and E. coli (D-value = 3.71 min) after only a plasma treatment time of 6 min using the FlatPlaSter device (fig. 3A/B). By increasing the plasma treatment time up to 15 min the killing efficacy was enhanced. Already a treatment time of 8 min achieved a killing efficacy of ≥5 log10 (99.999% of the initial applied bacteria were killed) for both bacteria strains. In order to investigate whether the observed reduction of methicillin-sensitive S. aureus was independent of the antibiotic resistance pattern, two different MRSA strains were treated with the FlatPlaSter under conditions identical to those for S. aureus and E. coli. Similar results were recorded when the MRSA strain BAA-44 was treated with different plasma treatment times (fig. 4). Already a plasma treatment time of 4 min resulted in a killing efficacy of MRSA (BAA-44) of 3 log10 steps (99.9%). Increasing the plasma treatment time to 8 min a killing efficacy of 5 log10 steps (99.999%) was achieved (D-value = 3.9 min). As expected, the plasma treatment of the second MRSA strain (atcc 43300) resulted in a substantial decrease of CFU ml−1 as well (D-value = 3.6 min). The mean reductions in CFU ml−1 were 3 log10 or 5 log10 upon plasma treatment of 4 or 8 min respectively (data not shown).
The second set of experiments was devoted to studying the efficiency of decolonisation of bacteria applied to ex vivo skin using the miniFlatPlaSter as a handheld device (fig. 2). Figure 5 shows the decrease of CFU ml−1 of S. aureus obtained with different plasma treatment times. A decrease of ∼3 log10 steps (∼99.9%) of viable S. aureus was achieved within 60 sec. Prolonging the plasma treatment to 5 min resulted in a killing efficacy of ≥3 log10 steps (≥99.9%) (fig. 5).
Cold atmospheric plasma treatment of S. aureus (107/ml) applied to ex vivo skin using the miniFlatPlaSter device. Different plasma treatment times were tested [sec]. A CFU assay was performed immediately after the plasma treatment. Black dotted line: baseline of viable bacteria per ml; red dotted line: reduction of one log10 step of viable bacteria (90%); green dotted line: reduction of three log10 steps of viable bacteria (99.9%). (n = 3, mean value ± standard deviation).
Viability of porcine skin after plasma treatment
In order to assess the influence of the plasma treatment time on the viability of the ex vivo porcine skin under experimental conditions a TUNEL assay was performed to analyse the number of DNA damaged cells within the epidermis within 48 h after treatment. Normal untreated skin samples embedded in Hepes Agar did not show any morphological changes up to 48 h after the treatment (data not shown). During the entire observation period a total of 12±6% of TUNEL-positive cells was counted within the epidermis of untreated samples. Plasma treatment regardless of the used plasma device and treatment time also showed no increase of TUNEL-positive cells within 24 h (fig. 6). Only a small fraction of positive stained, DNA damaged cells were detected within the upper layers of the epidermis after 48 h, but this was independently when the samples were treated or untreated (fig. 6E and 6F). No TUNEL-positve cells were detected within the dermis.
TUNEL staining of skin sections after the plasma treatment of skin samples inoculated with bacteria. (A) Positive control: incubation with 300 U DNase; (B) negative control; (C) immediately after the 15 min plasma treatment; (D) 24 h after the 15 min plasma treatment; (E) 48 h after the 15 min plasma treatment; (F) 48 h of an untreated skin sample (40×magnifications).
Discussion
In this study an ex vivo porcine skin model was used to evaluate the antimicrobial decolonisation efficacy of cold-atmospheric plasma against antibiotic-sensitive and resistant bacteria. The results demonstrate that killing of MRSA, S. aureus and E. coli by cold atmospheric plasma was time-dependent without harming the underlying tissue. Freshly excised porcine skin was used, because it is proposed as a good test model for human skin based on many physiological and anatomical similarities [18]. Histological evaluation of plasma-treated skin samples showed only a slight increase of TUNEL-positive cells within the epidermis, indicating that the porcine skin might be still vital. However 48 hours after the plasma treatment we could detect TUNEL-positive cells in both plasma-treated samples and the untreated controls. This means that the observed damage to the eukaryotic cells is not directly related to the plasma treatment rather than to the total cultivation time of the ex vivo porcine skin. Furthermore cold atmospheric plasma seems not to influence the underlying tissue, because no TUNEL-positive cells were detected at or below the basal membrane or the dermis. Bush and colleagues demonstrated in their studies the feasibility of pig skin as a model substrate for evaluating skin disinfectants [24]. However, in their study skin samples were frozen prior to evaluation of topically applied new antimicrobial agents. We, in this study, used freshly excised skin samples. In spite of this, the results obtained by Bush et al. are more related to the hand-washing technique than to test the efficacy of new antimicrobial techniques using vital skin samples [24]. Recently Messager et al. could demonstrate, when testing several liquid disinfectants that antiseptics were more active in combination with mechanical effects ex vivo [25]. The addition of a mechanical effect by drill rubbing of two skin samples against each other produced a significantly greater reduction of the bacterial load [25]. In this study we demonstrated for the first time, that cold atmospheric plasma achieved a killing efficacy of up to 99.999% against topically applied bacteria, inclusively MRSA, via a contactless procedure without damaging the surrounding tissue (Figs. 3, 4 and 5). Then non-linear bacterial reduction with regard to the plasma treatment time may have several reasons:
With the used bacterial concentration of 106–7 per ml and 0.1 ml applied to an area of at maximum 4 cm2 we get a bacterial load of 2.5×104–5 per cm2 which is in the range of what is found on human skin. For a typical bacterial cross sectional area of 2×10−8 cm2 this gives a probability of overlap of 5×10−4 to 5×10−3. This theoretical probability of overlap – assuming a homogeneous distribution - is negligible and so is biofilm formation. However, there could still be concentrations of bacteria in skin folds or follicles. This is something difficult to rule out. Our primary aim in this study was to investigate whether the plasma technique could be useful for the inactivation of an antibiotic-resistant planktonic bacteria strain on skin but some concentration fluctuations cannot be ruled out on “real” surfaces like skin. As we pointed out this may happen even when the bacteria density is low. This could then be one of the reasons why the bacterial reduction rate is not linear.
Furthermore the non-linear reduction can also be explained by the necessity of a certain treshold value: enough reactive species have to be generated by the respective plasma device -above this value bacteria can then be killed very efficiently.
Therefore we can only define an overall treatment time where we achieve a 3 or 5-log10 reduction of CFU/ml as described in the Results section.
Successful decolonisation of patients colonised with multi-resistant bacteria is of interest for controlling and preventing bacterial spread in hospital daily routine. Recently Krishna and colleagues reviewed the available literature on the use of disinfectants for MRSA decolonisation. They concluded that the clinical outcome of an octenidine/dihydrochlorine solution for eradication of MRSA varied strongly between 6% and 75% [26]. In a further study of Johnson et al. which examined the successful decolonisation of MRSA by means of an alcohol/chlorhexidine hygiene solution, the consumption of the disinfection solution increased from 5.7 to 28.6 L/1000 bed-days [27]. In another study successful decolonisation was achieved only in patients who completed the full decolonization treatment course for 5 days [28]. The decolonization treatment consisted of mupirocin nasal ointment, chlorhexidine mouth rinse, and full-body wash with chlorhexidine soap. In all these studies the success depends on how many body regions are colonised by MRSA, as well as on the compliance of the treatment protocol by the patients and the health care workers.
This emphasizes the need for the development of additional strategies for the decolonisation of bacteria. Cold atmospheric plasma typically delivers up to 1015 active molecules per cm2 and second. Here a plasma treatment time of approximately 6 min delivered up to 3×109 active molecules for 1 µm2, which were needed to destroy bacteria without any carrier medium. In contrast active ingredients of anti-disinfectants have to be immersed inside an appropriate carrier. When liquids are used for disinfection, the active molecule delivery rate is roughly 1024 cm−2 s−1.
Therefore it could be shown that the plasma treatment is very efficient and fast in comparison with liquid treatment.
It is still under investigation why plasma treatment is so effective. Recently, Kim et al. demonstrated a significant 3.83 log10 decrease of CFU of adherent S. aureus by employing a plasma discharge in liquid using a reconstructed human skin model [14]. In this study liquid between the area of interest and the plasma device was needed to generate reactive molecules to destroy the bacteria. This means that the plasma device needs direct contact to the area of interest. The advantage of the cold atmospheric plasma treatment, which was used here, is that no direct contact with the sample is necessary to kill the bacteria applied to the stratum corneum. Our hypothesis is that the plasma produced gas forms a “cocktail of reactive species” and due to synergetic properties, the bactericidal effect is very pronounced. There are three principal effects of plasma action: (I) permeabliisation of the cell wall/membrane, leading to leakage of potassium; (II) access of reactive species intracellular to induce oxidative/nitrosative burst; (III) direct chemical reaction to DNA damage. All the reactions depend on the non-equilibrium plasma chemistry (e.g. hydrogen denaturation for membrane permeabilisation, density of ROS and RNS species produced in air and then the reactions inside the cell – e.g. Fenton's reaction as an example, which involves H2O2). The chemical composition produced by the plasma varies with power and time and therefore might be designable so that no negative impact on eukaryotic cells occurs [29]. In case of the miniFlatPlaSter a larger density of chemically reactive species is produced with higher power input as compared to the FlatPlaSter and because of that the inactivation speed is faster (fig. 5). As described in the Results section both plasma devices used for this study produce - amongst others species - ozone in the ppm region. For sterilization of medical equipment or the in vivo treatment of infected skin areas, it is planned to include a filter system using a pump for toxic gas removal, to exchange the gas (air) between the respective plasma treatments and to produce a “sufficiently closed” volume which covers the area of interest. This means that the transmission of possibly toxic components can be avoided. Therefore the plasma is a good medium for energy transfer for inactivating bacteria applied to vital skin.
Overall, the results demonstrate the considerable potential of cold atmospheric plasma in decolonisation of pathogenic bacteria, which were applied to intact skin surfaces in vitro. Using two different plasma devices we were able to show, that a bacterial reduction of up to 3 log10 steps was achieved for a 60 sec (miniFlatPlaSter)/4 min (FlatPlaSter) plasma treatment; more than a 5 log10 reduction was achieved after 8 min (FlatPlaSter) of plasma treatment - without causing any damage to the porcine skin. Although the applicability of this special approach using these prototype devices is too long for hand disinfection at the moment, cold atmospheric plasma might be a powerful tool for topical contact-free use to prevent nosocomial transmission of multiresistant pathogens, like MRSA, because here the full decolonisation treatment course is much longer.
Acknowledgments
The excellent technical assistant of Judith Heider and Ewa Kowalewski is gratefully acknowledged.
Author Contributions
Conceived and designed the experiments: TM TS JLZ SK. Performed the experiments: TM TS YFL. Analyzed the data: TM TS YFL. Contributed reagents/materials/analysis tools: JH SK GM. Wrote the paper: TM TS YFL JLZ.
References
- 1. Arias CA, Murray BE (2009) Antibiotic-resistant bugs in the 21st century–a clinical super-challenge. N Engl J Med 360: 439–443.
- 2. Rice LB (2008) Federal funding for the study of antimicrobial resistance in nosocomial pathogens: no ESKAPE. J Infect Dis 197: 1079–1081.
- 3. Spellberg B, Guidos R, Gilbert D, Bradley J, Boucher HW, et al. (2008) The epidemic of antibiotic-resistant infections: a call to action for the medical community from the Infectious Diseases Society of America. Clin Infect Dis 46: 155–164.
- 4.
EARSS MT (2009) EARSS Annual Report 2008. pp. 55–57. Available: http://wwwrivmnl/en/.
- 5. Klevens RM, Edwards JR, Tenover FC, McDonald LC, Horan T, et al. (2006) Changes in the epidemiology of methicillin-resistant Staphylococcus aureus in intensive care units in US hospitals, 1992–2003. Clin Infect Dis 42: 389–391.
- 6. Zimmermann J, Dumler K, Shimizu T, Morfill G, Wolf A, et al. (2011) Effects of cold atmospheric plasmas on adenoviruses in solution. J Phys D: Appl Phys 44: 1–9.
- 7. Shimizu T, Zimmermann JL, Morfill GE (2011) The bactericidal effect of surface micro-discharge plasma under different ambient conditions. New Journal of Physics 13: 1–7.
- 8. Kong MG, Kroesen G, Morfill GE, Nosenko T, Shimizu T, et al. (2009) Plasma medicine: an introductory review. New Journal of Physics 11: 1–35.
- 9. Ermolaeva SA, Varfolomeev AF, Chernukha MY, Yurov DS, Vasiliev MM, et al. (2011) Bactericidal effects of non-thermal argon plasma in vitro, in biofilms and in the animal model of infected wounds. J Med Microbiol 60: 75–83.
- 10. Kelly-Wintenberg K, Montie TC, Brickman C, Roth JR, Carr AK, et al. (1998) Room temperature sterilization of surfaces and fabrics with a one atmosphere uniform glow discharge plasma. J Ind Microbiol Biotechnol 20: 69–74.
- 11. Joshi SG, Paff M, Friedman G, Fridman G, Fridman A, et al. (2010) Control of methicillin-resistant Staphylococcus aureus in planktonic form and biofilms: a biocidal efficacy study of nonthermal dielectric-barrier discharge plasma. Am J Infect Control 38: 293–301.
- 12. Cotter JJ, Maguire P, Soberon F, Daniels S, O'Gara JP, et al. (2011) Disinfection of meticillin-resistant Staphylococcus aureus and Staphylococcus epidermidis biofilms using a remote non-thermal gas plasma. J Hosp Infect 78: 204–207.
- 13. Burts ML, Alexeff I, Meek ET, McCullers JA (2009) Use of atmospheric non-thermal plasma as a disinfectant for objects contaminated with methicillin-resistant Staphylococcus aureus. Am J Infect Control 37: 729–733.
- 14. Kim PY, Kim YS, Koo IG, Jung JC, Kim GJ, et al. (2011) Bacterial inactivation of wound infection in a human skin model by liquid-phase discharge plasma. PLoS One 6: e24104.
- 15. Lademann O, Kramer A, Richter H, Patzelt A, Meinke MC, et al. (2011) Skin disinfection by plasma-tissue interaction: comparison of the effectivity of tissue-tolerable plasma and a standard antiseptic. Skin Pharmacol Physiol 24: 284–288.
- 16. Maisch T, Bosl C, Szeimies RM, Love B, Abels C (2007) Determination of the antibacterial efficacy of a new porphyrin-based photosensitizer against MRSA ex vivo. Photochem Photobiol Sci 6: 545–551.
- 17. Meyer W, Schwarz R, Neurand K (1978) The skin of domestic mammals as a model for the human skin, with special reference to the domestic pig. Curr Probl Dermatol 7: 39–52.
- 18. Simon GA, Maibach HI (2000) The pig as an experimental animal model of percutaneous permeation in man: qualitative and quantitative observations–an overview. Skin Pharmacol Appl Skin Physiol 13: 229–234.
- 19. Morfill GE, Shimizu T, Steffes B, Schmidt H-U (2009) Nosocomial infections—a new approach towards preventive medicine using plasmas. New Journal of Physics 11: 10.
- 20. Miles AA, Misra SS, Irwin JO (1938) The estimation of the bactericidal power of the blood. J Hyg (Lond) 38: 732–749.
- 21. Schacht V, Becker K, Szeimies RM, Abels C (2002) Apoptosis and leucocyte-endothelium interactions contribute to the delayed effects of cryotherapy on tumours in vivo. Arch Dermatol Res 294: 341–348.
- 22. Boyce JM, Pittet D (2002) Guideline for Hand Hygiene in Health-Care Settings. Recommendations of the Healthcare Infection Control Practices Advisory Committee and the HIPAC/SHEA/APIC/IDSA Hand Hygiene Task Force. Am J Infect Control 30: S1–46.
- 23. Lee K, Paek KH, Ju WT, Lee Y (2006) Sterilization of bacteria, yeast, and bacterial endospores by atmospheric-pressure cold plasma using helium and oxygen. J Microbiol 44: 269–275.
- 24. Bush LW, Benson LM, White JH (1986) Pig skin as test substrate for evaluating topical antimicrobial activity. J Clin Microbiol 24: 343–348.
- 25. Messager S, Goddard PA, Dettmar PW, Maillard JY (2004) Comparison of two in vivo and two ex vivo tests to assess the antibacterial activity of several antiseptics. J Hosp Infect 58: 115–121.
- 26. Krishna BV, Gibb AP (2010) Use of octenidine dihydrochloride in meticillin-resistant Staphylococcus aureus decolonisation regimens: a literature review. J Hosp Infect 74: 199–203.
- 27. Johnson PD, Martin R, Burrell LJ, Grabsch EA, Kirsa SW, et al. (2005) Efficacy of an alcohol/chlorhexidine hand hygiene program in a hospital with high rates of nosocomial methicillin-resistant Staphylococcus aureus (MRSA) infection. Med J Aust 183: 509–514.
- 28. Buehlmann M, Frei R, Fenner L, Dangel M, Fluckiger U, et al. (2008) Highly effective regimen for decolonization of methicillin-resistant Staphylococcus aureus carriers. Infect Control Hosp Epidemiol 29: 510–516.
- 29. Liebmann J, Scherer J, Bibinov N, Rajasekaran P, Kovacs R, et al. (2011) Biological effects of nitric oxide generated by an atmospheric pressure gas-plasma on human skin cells. Nitric Oxide 24: 8–16.