Skip to main content
Advertisement
  • Loading metrics

Anti-infective Surface Coatings: Design and Therapeutic Promise against Device-Associated Infections

  • Bryan R. Coad ,

    bryan.coad@unisa.edu.au

    Affiliation Future Industries Institute, University of South Australia, Mawson Lakes, South Australia, Australia

  • Hans J. Griesser,

    Affiliation Future Industries Institute, University of South Australia, Mawson Lakes, South Australia, Australia

  • Anton Y. Peleg,

    Affiliations Infection and Immunity Program and the Department of Microbiology, Biomedicine Discovery Institute, Monash University, Clayton, Victoria, Australia, Department of Infectious Diseases, Central Clinical School, Alfred Hospital and Monash University, Melbourne, Victoria, Australia

  • Ana Traven

    Affiliation Infection and Immunity Program and the Department of Biochemistry and Molecular Biology, Biomedicine Discovery Institute, Monash University, Clayton, Victoria, Australia

Introduction

Patient safety and well-being are under increasing threat from hospital-acquired infections [1]. The root cause of a large number of these infections arises from microbial biofilms that colonise on surfaces of medical devices such as the millions of catheters, endotracheal tubes, and prosthetics implanted every year [2]. Biofilm infections are accompanied by increased resistance to antimicrobial therapy and immune clearance, severely limiting treatment options and leading to life-threatening disease [3,4]. Device-associated infections are caused by both bacteria and fungi and, while most studies have focused on single-species biofilms, biofilm-related infections are often polymicrobial [58]. Multi-species biofilms, particularly those involving bacterial and fungal pathogens, are more challenging to treat, likely as a consequence of their combined architecture, protective extracellular matrix, and potential synergism in protecting against antimicrobials and host immunity [911]. Among the fungi, Candida species are the most important biofilm pathogens [12,13] and the fourth leading cause of blood-stream infections in United States hospitals [7]. Fungal diseases remain difficult to diagnose, mortality rates remain high, and antifungal drug resistance continues to limit therapeutic options [14,15]. We are in desperate need of innovative strategies that target the mechanisms of pathogenesis of polymicrobial biofilms on medical devices. This is a grand challenge because it requires multi-disciplinary collaboration and breakthrough research involving physical chemistry, materials science, and microbiology. Communication between these disciplines has not been common, but recent advances show greater convergence in the development of anti-infective devices. At this nexus, we outline the therapeutic promise of anti-infective coatings for medical devices and discuss pitfalls and strategies for overcoming them.

Stopping Biofilm Formation before It Starts

A key step in biofilm formation is the initial adherence to the surface [16,17]. Once attached, the infectious agents replicate, colonise the device, and embed themselves within a protective extracellular matrix. Biofilm drug resistance is thought to be caused by several mechanisms, including sequestering of drugs, persister cells, and specific aspects of biofilm cell physiology [18,19]. One solution is to kill or prevent adhesion of pathogens on medical devices via delivery of antibiotics from the surface of materials/devices, which would allow for a high concentration of the drugs at the implantation site [20]. Research has been devoted to novel antimicrobial agents such as cationic compounds, semi or fully synthetic antimicrobial peptides, or the use of silver [2124]. While these approaches have significant advantages, such as the ability to physically disrupt the microbial membrane (a mechanism by which microbes may have difficulty developing resistance), there are also disadvantages. One is that the safety of such compounds needs to be demonstrated to show selectivity for preferentially lysing only pathogenic membranes over mammalian cells—and importantly, this window of selectivity becomes even narrower when discriminating between eukaryotic cell types (e.g., fungi and mammalian cells). As a result, new compounds will require a prolonged regulatory approval process to demonstrate their safety, ultimately slowing development. Devices utilising commercially available pharmaceuticals would expedite the development process. In either case, particularly for vascular devices, the potential for interaction between surface compounds and drugs or other compounds administered via the device will require testing to ensure regulatory standard. In light of these issues, we focus this short review towards antimicrobial surfaces that use approved pharmaceuticals.

One way to deliver antimicrobial pharmaceuticals is by coatings that act by “drug release.” This approach involves pre-loading the surface coating with a reservoir of drug that, once implanted, gradually diffuses into the fluids and tissues surrounding the implant, providing a high local dose of the drug [25]. Another strategy is “tethered drug surfaces,” on which the antimicrobial pharmaceuticals are attached by means of chemical bonds directly to the surface or a surface interlayer. Fig 1 compares the key aspects of these coatings and lists advantages and disadvantages relating to their possible clinical use and mechanism of action.

thumbnail
Fig 1. Important factors in the design of anti-infective materials and their surface coatings.

https://doi.org/10.1371/journal.ppat.1005598.g001

Whether novel or approved antimicrobial agents are used, the ability for infectious agents to develop resistance is a growing concern. Drug-releasing coatings create a local concentration gradient, reaching diminishingly small concentrations (eventually below the Minimum Inhibitory Concentration [MIC]) that may promote antimicrobial resistance in the context of a localised infection. Tethered coatings maintain a high local concentration on the device periphery, which circumvents this issue [26].

Surface-Attached Pharmaceuticals: Promises

Tethered drug surfaces are a particularly interesting area of fundamental research because of the potential to uncover new mechanisms of action for “old” drugs. In other words, we are greatly interested in how the antimicrobials are presented from the surface, whether they would find existing or new targets within the cell wall or membrane, and the chemical and biophysical result of interactions with microbes that might delay the acquisition of resistance phenotypes. These mechanisms could be different from their solution-based understanding, thus driving innovation in drug formulation [27]. This particular aspect would be of great commercial interest to pharmaceutical companies or drug formulators as an opportunity to add value to, or find novel mechanisms for, their existing or non-profitable chemical libraries.

Surface-Attached Pharmaceuticals: Pitfalls

Tethered drug surfaces are prepared by forming a chemical bond between functional groups on the drug target and groups on the surface or surface coating. In order for the benefits of a tethered drug surface to be achieved (Fig 1 and see below for additional discussion) it is essential that (1) the drug is and remains covalently bound to the surface and (2) it can be analytically verified that drugs are not released from the surface. The first point presents a major technical challenge because large excesses of compounds must be used when preparing surfaces [28]. When excess compound is present during binding, only a small fraction of drug can become chemically attached in a monolayer (i.e., chemisorbed or irreversibly bound through the formation of a covalent bond) to the surface. The major portion will instead much more readily associate weakly into physically adsorbed (i.e., physisorbed) layers or multilayers, in which drugs are held together by weak interfacial bonds that have the potential to be reversed over time or in different solution environments (e.g., ionic strength, pH, polarity, and physiological temperature). While washing steps are used to remove this excess, there is a pitfall in assuming that one (or even multiple) washing steps will be sufficient because washing solutions might not be able to readily disrupt weak bonds.

For antimicrobial pharmaceuticals that inhibit cell wall synthesis or otherwise compromise cell wall integrity, tethering them to surfaces is a logical strategy, thus allowing them to interface with targets in the cell envelope. One promising candidate is caspofungin: an antifungal lipopeptide that inhibits 1, 3 β glucan synthase and thus disrupts fungal cell wall biogenesis [29]. Another is vancomycin, which binds to cell wall peptides of Gram-positive bacteria and prevents crosslinking [30]. Coad et al. demonstrated that a covalent caspofungin coating that can be applied to a variety of biomaterials kills the four most common Candida species causing device-associated infections [31]. Kucharíková et al. demonstrated both caspofungin and vancomycin tethering to surface coatings (separately) on titanium implant devices and showed their in vitro and in vivo efficacy against Candida albicans and Staphylococcus aureus [32]. To understand the mechanism of action, analytical evidence can demonstrate whether these antimicrobial agents are covalently attached to their surface or whether they might reversibly desorb. Surface-sensitive techniques such as X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) can be used to show the presence of caspofungin on surface coatings. Using these analytical approaches, it has been demonstrated that even after extensive water and buffer washing, physisorption dominated over covalent attachment and was responsible for the majority of the caspofungin detected (66%) [31]. Only after extended washing with elevated temperature and surfactant could all traces of physisorbed compound be removed. These covalently bound caspofungin samples were effective using in vitro studies [31]. Other analytical techniques such as high performance liquid chromatography (HPLC) and scanning electron microscopy (SEM) have also been used to provide quantitative and qualitative evidence for the presence of bound drugs. Using these techniques, vancomycin was shown to bind to surfaces with monolayer coverage, which is possible through physisorption and/or chemisorption [32]. The same study found that caspofungin binding resulted in multilayers [32], which is only possible when physisorbed, thus suggesting that only a fraction of the compound was covalently attached to the surface.

Further studies with tethered drugs illustrate the importance of assessing the physical or chemical properties of surfaces and their coatings. Antibacterial drugs such as tetracycline and levofloxacin require penetration of the drug into the cell cytosol to interact with their intercellular targets. Therefore, surface coatings with these drugs tethered would need to provide sufficient linker length and conformational flexibility to penetrate through the network of membrane and cell wall biomolecules to span the cell envelope thickness of approximately 40–50 nm [33]. With tetracycline, Davidson et al. suggested that covalent attachment of the drug to ethylene oxide linkers was responsible for penetration into the Gram-negative cell wall allowing for elimination of Escherichia coli [34]. The linkers used in the chemical synthesis could theoretically stretch to 6–7 nm in length, but the physical forces governing chain conformations in biological fluids would further limit the distance in vivo. Thus an alternative explanation for antibacterial effect is likely through a novel mechanism of action or release of the drug from the surface entering the cell. Consistent with the idea that release of adsorbed compounds by desorption or hydrolysis could explain the mode of action of intercellularly acting drugs, Kugel covalently attached levofloxacin to surfaces and observed killing of E. coli, and the antibacterial effect was suggested to be release of levofloxacin from hydrolytically unstable tethers [35].

Compared to antibacterial coatings, the need for developing antifungal biomaterials has received far less attention [27], but it is an essential prerequisite for developing hybrid strategies for combatting polymicrobial device infections. As illustrated by the examples above [31,32], the demonstrated antifungal effect in vitro and in vivo of surfaces coated with caspofungin show promise for future development of device coatings that could be beneficial against polymicrobial infections. The need to design materials that eliminate multi-species or cross-domain infections will require hybrid approaches that could involve not only pharmaceuticals but also novel agents such as cationic compounds or antimicrobial peptides that are broadly antibacterial and antifungal and likely to incorporate both tethering and releasing strategies. However, caution will be needed to ensure that these coatings are safe and compatible with host cells.

Complex Problems Requiring Multidisciplinary Solutions

Advances in coatings for biomedical devices are likely to develop from new, fundamental studies in materials science, engineering, and nanotechnology. It can be seen that in these disciplines, an increasing number of publications focus on antimicrobial surface coatings and their understanding [27]. As discussed, there are challenges in fabricating anti-infective tethered drug coatings, but recent work has shown that covalent attachment of antimicrobial compounds to surfaces is achievable and effective, although more understanding is needed. Surfaces with non-desorbing compounds that operate through novel, surface-associated mechanisms of action will be an innovative component of future anti-infective medical device surface coatings that are long lasting. As described above, the important role of physisorption, hydrolysis, and chemical structure should be considered in evaluating the mechanism of action. Progress will also be helped by knowledge about surface-sensitive analytical instrumentation, the strengths and limitations of such techniques, and their role in understanding surface phenomena. Admittedly, the need for better physicochemical understanding of surfaces by materials scientists is not being communicated to the wider biological community, likely due to lack of discourse between disciplines. So, too, is a greater need for materials-led research to be relevant to the biological and clinical communities so that it becomes an effective tool for the microbial pathogenesis community, clinician, and end-user. Multidisciplinary consortia to tackle these important challenges and educating peers to critically evaluate this work will pave the path to developing effective and novel therapeutic strategies for problematic biofilm-related infections.

References

  1. 1. Klevens RM, Edwards JR, Richards CL, Horan TC, Gaynes RP, et al. (2007) Estimating Health Care-Associated Infections and Deaths in U.S. Hospitals, 2002. Public Health Reports (1974-) 122: 160–166.
  2. 2. Busscher HJ, van der Mei HC, Subbiahdoss G, Jutte PC, van den Dungen JJ, et al. (2012) Biomaterial-associated infection: locating the finish line in the race for the surface. Sci Transl Med 4: 153rv110.
  3. 3. Cuellar-Cruz M, Vega-Gonzalez A, Mendoza-Novelo B, Lopez-Romero E, Ruiz-Baca E, et al. (2012) The effect of biomaterials and antifungals on biofilm formation by Candida species: a review. Eur J Clin Microbiol Infect Dis 31: 2513–2527. pmid:22581304
  4. 4. Hidron AI, Edwards JR, Patel J, Horan TC, Sievert DM, et al. (2008) NHSN annual update: antimicrobial-resistant pathogens associated with healthcare-associated infections: annual summary of data reported to the National Healthcare Safety Network at the Centers for Disease Control and Prevention, 2006–2007. Infection Control and Hospital Epidemiology 29: 996–1011. pmid:18947320
  5. 5. Luis G-R, Telenti A, Rodney LT, Glenn DR (1989) Polymicrobial Fungemia: Microbiology, Clinical Features, and Significance. Reviews of Infectious Diseases 11: 208–212. pmid:2704925
  6. 6. Peleg AY, Hogan DA, Mylonakis E (2010) Medically important bacterial-fungal interactions. Nat Rev Microbiol 8: 340–349. pmid:20348933
  7. 7. Kojic EM, Darouiche RO (2004) Candida infections of medical devices. Clinical microbiology reviews 17: 255–267. pmid:15084500
  8. 8. Peleg AY, Hooper DC (2010) Hospital-acquired infections due to gram-negative bacteria. New England Journal of Medicine 362: 1804–1813. pmid:20463340
  9. 9. Klotz SA, Chasin BS, Powell B, Gaur NK, Lipke PN (2007) Polymicrobial bloodstream infections involving Candida species: analysis of patients and review of the literature. Diagnostic Microbiology and Infectious Disease 59: 401–406. pmid:17888612
  10. 10. Harriott MM, Noverr MC (2011) Importance of Candida-bacterial polymicrobial biofilms in disease. Trends Microbiol 19: 557–563. pmid:21855346
  11. 11. Shirtliff ME, Peters BM, Jabra-Rizk MA (2009) Cross-kingdom interactions: Candida albicans and bacteria. FEMS Microbiol Lett 299: 1–8. pmid:19552706
  12. 12. Chandra J, Mukherjee PK, Ghannoum MA (2012) Candida biofilms associated with CVC and medical devices. Mycoses 55: 46–57.
  13. 13. Ferreira AV, Prado CG, Carvalho RR, Dias KS, Dias AL (2013) Candida albicans and non-C. albicans Candida species: comparison of biofilm production and metabolic activity in biofilms, and putative virulence properties of isolates from hospital environments and infections. Mycopathologia 175: 265–272. pmid:23532754
  14. 14. Brown GD, Denning DW, Gow NA, Levitz SM, Netea MG, et al. (2012) Hidden killers: human fungal infections. Sci Transl Med 4: 165rv113.
  15. 15. Wisplinghoff H, Bischoff T, Tallent SM, Seifert H, Wenzel RP, et al. (2004) Nosocomial bloodstream infections in US hospitals: analysis of 24,179 cases from a prospective nationwide surveillance study. Clin Infect Dis 39: 309–317. pmid:15306996
  16. 16. Chandra J, Kuhn DM, Mukherjee PK, Hoyer LL, McCormick T, et al. (2001) Biofilm formation by the fungal pathogen Candida albicans: Development, architecture, and drug resistance. Journal of Bacteriology 183: 5385–5394. pmid:11514524
  17. 17. Costerton JW, Stewart PS, Greenberg E (1999) Bacterial biofilms: a common cause of persistent infections. Science 284: 1318–1322. pmid:10334980
  18. 18. Stewart PS, Costerton JW (2001) Antibiotic resistance of bacteria in biofilms. Lancet 358: 135–138. pmid:11463434
  19. 19. Ramage G, Mowat E, Jones B, Williams C, Lopez-Ribot J (2009) Our current understanding of fungal biofilms. Crit Rev Microbiol 35: 340–355. pmid:19863383
  20. 20. Bachmann SP, VandeWalle K, Ramage G, Patterson TF, Wickes BL, et al. (2002) In Vitro Activity of Caspofungin against Candida albicans Biofilms. Antimicrobial Agents and Chemotherapy 46: 3591–3596. pmid:12384370
  21. 21. Monteiro DR, Gorup LF, Takamiya AS, Ruvollo AC, Camargo ER, et al. (2009) The growing importance of materials that prevent microbial adhesion: antimicrobial effect of medical devices containing silver. International Journal of Antimicrobial Agents 34: 103–110. pmid:19339161
  22. 22. Campoccia D, Montanaro L, Arciola CR (2013) A review of the biomaterials technologies for infection-resistant surfaces. Biomaterials 34: 8533–8554. pmid:23953781
  23. 23. Swartjes J, Sharma PK, van Kooten TG, van der Mei HC, Mahmoudi M, et al. (2015) Current Developments in Antimicrobial Surface Coatings for Biomedical Applications. Current Medicinal Chemistry 22: 2116–2129. pmid:25245508
  24. 24. Salwiczek M, Qu Y, Gardiner J, Strugnell RA, Lithgow T, et al. (2014) Emerging rules for effective antimicrobial coatings. Trends in Biotechnology 32: 82–90. pmid:24176168
  25. 25. Zumbuehl A, Ferreira L, Kuhn D, Astashkina A, Long L, et al. (2007) Antifungal hydrogels. Proc Natl Acad Sci U S A 104: 12994–12998. pmid:17664427
  26. 26. Kugel A, Stafslien S, Chisholm BJ (2011) Antimicrobial coatings produced by “tethering” biocides to the coating matrix: A comprehensive review. Progress in Organic Coatings 72: 222–252.
  27. 27. Coad BR, Kidd SE, Ellis DH, Griesser HJ (2014) Biomaterials surfaces capable of resisting fungal attachment and biofilm formation. Biotechnology advances 32: 296–307. pmid:24211473
  28. 28. For example, a typical reaction may use solution concentrations on the order of 1 mg mL-1, the, if the final surface density of the compound (assuming flat surface) is 1 ng cm-2, the surface was exposed to a million-fold excess of compound.
  29. 29. Perlin DS (2011) Current perspectives on echinocandin class drugs. Future Microbiol 6: 441–457. pmid:21526945
  30. 30. Reynolds PE (1989) Structure, biochemistry and mechanism of action of glycopeptide antibiotics. European Journal of Clinical Microbiology and Infectious Diseases 8: 943–950. pmid:2532132
  31. 31. Coad BR, Lamont-Friedrich SJ, Gwynne L, Jasieniak M, Griesser SS, et al. (2015) Surface coatings with covalently attached caspofungin are effective in eliminating fungal pathogens. Journal of Materials Chemistry B 3: 8469–8476.
  32. 32. Kucharíková S, Gerits E, De Brucker K, Braem A, Ceh K, et al. (2015) Covalent immobilization of antimicrobial agents on titanium prevents Staphylococcus aureus and Candida albicans colonization and biofilm formation. Journal of Antimicrobial Chemotherapy.
  33. 33. Meroueh SO, Bencze KZ, Hesek D, Lee M, Fisher JF, et al. (2006) Three-dimensional structure of the bacterial cell wall peptidoglycan. Proceedings of the National Academy of Sciences of the United States of America 103: 4404–4409. pmid:16537437
  34. 34. Davidson H, Poon M, Saunders R, Shapiro IM, Hickok NJ, et al. (2015) Tetracycline tethered to titanium inhibits colonization by Gram-negative bacteria. Journal of Biomedical Materials Research Part B: Applied Biomaterials 103: 1381–1389.
  35. 35. Kugel A, Chisholm B, Ebert S, Jepperson M, Jarabek L, et al. (2010) Antimicrobial polysiloxane polymers and coatings containing pendant levofloxacin. Polymer Chemistry 1: 442.